The ANCOREX can be mounted on the Gliding Mount, QD Mount, and Stationary Mount. These are the only mounts compatible with the ANCOREX.

The ANCOREX can be mounted on the Gliding Mount, QD Mount, and Stationary Mount. These are the only mounts compatible with the ANCOREX.&#xA0;

What are the mounting options for the ANCOREX?

All ANCORE and ANCORE Pro mounts are not compatible with the ANCOREX.

All ANCORE and ANCORE Pro mounts are not compatible with the ANCOREX.&#xA0;

Are the mounts for the ANCORE and ANCORE Pro compatible with the ANCOREX?

The Stationary Mount works with both 2x3 and 3x3 racks with both 5/8th and 1 inch holes, hole spacing must be 1 or 2 inches.

The Stationary Mount works with both 2x3 and 3x3 racks with both 5/8th and 1 inch holes, hole spacing must be 1 or 2 inches. &#xA0;

Is the Stationary Mount for ANCOREX compatible with my rack?

The Gliding Mount is compatible with any 3x3 rack or rig and does not require the use of any rack holes.

The Gliding Mount is compatible with any 3x3 rack or rig and does not require the use of any rack holes.&#xA0;

Is the Gliding Mount for ANCOREX compatible with my rack?

The QD Mount works with both 2x3 and 3x3 racks with both 5/8th and 1 inch holes, hole spacing must be 1 or 2 inches.

The QD Mount works with both 2x3 and 3x3 racks with both 5/8th and 1 inch holes, hole spacing must be 1 or 2 inches.&#xA0;

Is the QD Mount for ANCOREX compatible with my rack?

Choose your desired height on your rack/uprightMatch the pegs with the holes on the rack/uprightWhile holding the plate mount interface screw the wingnuts onto the pegs until the wingnuts are tight and the mount is secureSlide the ANCOREX onto the pl

<ol id="isPasted"><li>Choose your desired height on your rack/upright</li><li>Match the pegs with the holes on the rack/upright</li><li>While holding the plate mount interface screw the wingnuts onto the pegs until the wingnuts are tight and the mount is secure</li><li>Slide the ANCOREX onto the plate mount interface until you hear a click</li><li>Once you hear the click you are ready to begin training!</li></ol>

How do I set up the Stationary Rack Mount?

Choose your desired height on your rack/uprightMatch the pegs with the holes on the rack/uprightWhile holding the plate mount interface grab your spring-lock knobs, press and hold the button and slide the knob onto the pegs until it’s almost snugLet

<ol id="isPasted"><li>Choose your desired height on your rack/upright</li><li>Match the pegs with the holes on the rack/upright</li><li>While holding the plate mount interface grab your spring-lock knobs, press and hold the button and slide the knob onto the pegs until it&#x2019;s almost snug</li><li>Let go of the button and give the knob a quarter or half turn and the mount should be secure</li><li>Slide the ANCOREX onto the plate mount interface until you hear a click</li></ol>

How do I set up the QD Mount

Step 1: Disassemble the Mount. Step 2: Position the Mount. Step 3: Reinstall the Bolts and Rollers Where They Were. Step 4: Unlock and Secure the Handle. Step 5: Mount the ANCOREX

Step 1: Disassemble the Mount &#xA0;<ol><li>The Gliding Mount comes lightly pre-assembled. To begin setup, you&#x2019;ll need to remove the set of loosely assembled rollers.&#xA0;</li><li>Using the provided 1/2in wrench &amp; 3/16in hex wrench, unscrew the black flanged nuts from the Precision Shoulder Bolts that run through the rollers.&#xA0;</li><li>Once unscrewed, remove the nuts, bolts &amp; rollers. Your mount will now be shaped like a &#x2018;C&#x2019;&#xA0;</li></ol>Step 2: Position the Mount&#xA0;<ol><li>Place the mount against your rack (or any 3in x 3in rounded square tubing) in a comfortable location so the remaining rollers are pressed against the rack.&#xA0;</li><li>The flat side of the plastic cover by the handle should be facing the ceiling.&#xA0;</li><li>Hold it steady against your racking while preparing the rollers and rods. This is best done when the mount is supported from below.&#xA0;</li></ol>Step 3: Reinstall the Bolts and Rollers Where They Were&#xA0;<ol><li>There are 3 sets of holes that allow the mount to find the best fit for your rack. The set closest to the top/bottom of the mount are the best ones to start with.&#xA0;</li><li>Hold your first roller against the rack on the side opposite the handle and line up the roller&#x2019;s hole with the open holes on the side of the unit. If you can see through the hole in the side of the mount, that will help in determining the appropriate alignment for the roller.&#xA0;</li><li>With the first roller held in place, initially insert a shoulder bolt (long rod) through the side with the ANCOREX Mounting Plate. The Precision Shoulder bolt should go through, the side hole &#x2192; through the roller &#x2192; and out the far side of the mount until the head of the Shoulder Bolt is seated flush against the aluminum wall. &#xA0;</li><li>Direction matters a lot. It will not work if the shoulder bolts are installed backwards.&#xA0;</li><li>Install the 2nd roller similarly to how the first one was installed, making sure that the 2nd roller is in the corresponding hole set to the 1st one. If the first roller is in the Top most hole, than the 2nd roller goes into the Bottom most hole.&#xA0;</li><li>Using the 1/2in Spanner Wrench and 3/16in hex wrench, tighten the nuts onto the shoulder bolts&#xA0;</li></ol>Step 4: Unlock and Secure the Handle&#xA0;<ol><li>Almost there. Undo the two bright red-capped screws located near the handle of the unit. This will unlock the handle, and it will rush towards the rack, allowing the mount to clamp securely to your rack/upright.&#xA0;</li><li>These screws will feel tight. While holding the mount in place on the rack, lift the handle while unscrewing the red caps.&#xA0;</li><li>Once removed, screw the red caps into the storage holes on the back side of the mount so they don&#x2019;t go missing. All eight (8) threaded holes are safe to store them in.&#xA0;</li></ol>Step 5: Mount the ANCOREX&#xA0;<ol><li>Align the bottom of the ANCOREX align with the top of the mount plate interface.&#xA0;</li><li>Slide the ANCOREX onto the plate mount interface of the Gliding Mount from top to bottom.&#xA0;</li><li>Once you hear a &quot;Click&quot;, it&#x2019;s locked in and ready to use.&#xA0;</li></ol>

How do I set up the Gliding Rack Mount?

Chat with a member of our team for product recommendations and help.

Want to bring ANCORE to your physical therapy practice or training facility? Have a question about your setup? Looking for a virtual demo? Our best-in-class customer service team is here to help.

Have a question? Give us a call. Any calls received outside help hours will be responded to the following business day.

Back to Website

ANCORE

Learn more about the ANCOREX Mount family, which one is right for you, and how to install them.

ANCOREX Mount Setups